View PI5V330A_702556.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PI5V330A Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux
Features:
* * * * * * * * * High-performance solution to switch between video sources Wide bandwidth: >360 MHz Low On-Resistance: 3 Low crosstalk at 10 MHz: -58dB Ultra-low quiescent power (0.1A typical) Single supply operation: +5.0V Fast switching: 10ns High-current output: 100mA Packaging (Pb-free & Green available): - 16-pin 300-mil wide plastic SOIC (S) - 16-pin 150-mil wide plastic SOIC (W) - 16-pin 150-mil wide plastic QSOP (Q)
Description:
Pericom Semiconductor's PI5V330A is a true bidirectional Quad 2-channel multiplexer/demultiplexer that is recommended for both RGB and composite video switching applications. The Video Switch can be driven from a current output RAMDAC or voltage output composite video source. Low On-Resistance and wide bandwidth make it ideal for video and other applications. Also this device has exceptionally high current capability which is far greater than most analog switches offered today. A single 5V supply is all that is required for operation. The PI5V330A offers a high-performance, low-cost solution to switch between video sources. The application section describes the PI5V330A replacing the HC4053 multiplier and buffer/ amplifier.
Block Diagram
S1A S2A S1B S2B S1C S2C S1D S2D
Pin Diagram
DA DB DC DD DECODER/DRIVERS EN IN IN 1A S
S2A
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
VCC EN S1D
S2D
DA
S1B S2B
DD
S1C S2C
DB GND
DD
Truth Table
EN 0 0 1 IN 0 1 X ON Switch
S1A, S1B, S1C, S1D S2A, S2B, S2C, S2D
Pin Description
Pin Name
S1A, S1B, S1C, S2A, S2B, S2C,
Description Analog Video I/O Select Input Enable Analog Video I/O Ground Power
PS8695B 03/01/05
S1D, S2D
Disabled
IN EN DA, DB, DC, DD GND VCC
1
PI5V330A Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ..........................................................-65C to +150C Ambient Temperature with Power Applied .........................-40C to +85C Supply Voltage to Ground Potential (Inputs & VCC Only)...-0.5V to +7.0V Supply Voltage to Ground Potential (Outputs & D/O Only) -0.5V to +7.0V DC Input Voltage ..................................................................-0.5V to +7.0V DC Output Current.............................................................................120mA Power Dissipation .................................................................................0.5W
Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
DC Electrical Characteristics (Over the Operating Range, TA = -40C to +85C, VCC = 5V 5%)
Parameters VANALOG VIH VIL IIH IIL IO VIK IOS VH RON Description Analog Signal Range Input HIGH Voltage Input LOW Voltage Input HIGH Current Input LOW Current Analog Output Leakage Currnet Clamp Diode Voltage Short Circuit Current(3) Input Hysteresis at Control Pins Switch On-Resistance Guaranteed Logic HIGH level Guaranteed Logic LOW Level VCC = Max., VIN = VCC VCC = Max., VIN = GND 0 S1, S2, or D VCC, Switch OFF VCC = Min., IIN = -18mA VCC = MIN., VIN = 1.0V RL = 75, ION = 13 mA VCC = MIN., VIN = 2.0V RL = 75, ION = 26 mA 3 -0.7 -1.2 150 3 7 7 10 Test Conditions(1) Min. 0 2.0 -0.5 0.8 1 1 1 V mA mV A Typ.(2) Max. 2.0 V Units
Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 5.0V, TA = 25C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between S1, S2, and D I/O pins at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the S1, S2, and D I/O pins.
2
PS8695B
03/01/05
PI5V330A Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Dynamic Characteristics (Over the Operating Range, TA = -40C to +85C, VCC = 5V 5%)
Parameters TON TOFF BW(1) XTALK DG DP CIN
(1) (1)
Description Turn On Time Turn Off Time -3dB Bandwidth Crosstalk Differential Gain Differential Phase Input/Enable Capacitance Capacitance, Switch Off Capacitance, Switch On Off Isolation
Test Conditions RL = 70, CL = 20PF, See Fig. 6 RL = 70, CL = 20PF, See Fig. 6 RL = 150, See Fig. 7 RIN = 10; RL = 150, 10MHz, See Fig. 7 RL = 150, f = 3.58 MHz, See Fig. 5 RL = 150, f = 3.58 MHz, See Fig. 5 VIN = 0V, f = 1 MHz VIN = 0V, f = 1 MHz VIN = 0V, f = 1 MHz RL = 150, 10MHz, See Fig 7
Min.
Typ. 2.5 1.1 -58 0.64 0.27
Max. 5 5 400
Unit ns MHz dB % Deg.
6 6 8 -38 dB pF
COFF OIRR
CON(1)
Notes: 1. This parameter is determined by device characterization but is not production tested.
Power Supply Characteristics
Parameters ICC ICC Description Quiescent Power Supply Current Supply Current per Input @ TTL HIGH Supply Current per Input per MHz(4) VCC = Max. VCC = Max. VCC = Max., S1, S2 and D Pins Open EN = GND Control Input Toggling 50%Duty Cycle Test Conditions(1) IN = GND or VCC IN = 3.4V(3) Min. Typ(2) 0.1 Max. 3.0 2.5 Units A mA mA/ MHz
ICCD
0.25
Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at VCC = 5.0V, +25C ambient. 3. Per TTL driven input (VI = 3.4V, control inputs only); S1, S2, and D pins do not contribute to Icc. 4. This current applies to the control inputs only and represent the current required to switch internal capacitance at the specified frequency. The S1, S2, and D I/O pins generate no significant AC or DC currents as they transition. This parameter is not tested, but is guaranteed by design.
N
3
PS8695B
03/01/05
PI5V330A Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Definitions
Symbol RON IO VIN VEN CIN COFF CON VIH VIL IIH (IIL) IOS tON tOFF BW XTALK DG DP OIRR Description Resistance between source and drain with switch in the ON state. Output leakage current measured at S1, S2, and D with the switch OFF. Digital voltage at the IN pin that selects between S1 and S2 analog inputs. A voltage that ENABLES the chip. Capacitance at the digital inputs. Capacitance at analog I/O (S1, S2, D) with switch OFF. Capacitance at analog I/O (S1, S2, D) with switch ON. Minimum input voltage for logic HIGH. Minimum input voltage for logic LOW. Input current of the digital input. Minimum short circuit current for S1, S2 and D. Propagation delay measured between 50% of the digital input to 90% of the analog output when switch is turned ON. The peak analog voltage is 0.714V. Propagation delay measured between 50% of the digital input to 90% of the analog output when switch is turned OFF. The peak analog voltage is 0.714V. Frequency response of the switch in the ON state measured at 3dB down. Is an unwanted signal coupled from channel to channel. Measured in -dB. XTALK = 20 LOG VOUT/VIN. This is non-adjacent crosstalk. Differential gain is the difference measurement between two bias levels, for instance analog input signals of 0V to 0.714V. Differential phase is the difference measurement between two bias levels, for instance analog input signals of 0V to 0.714V. Off isolation is the resistance (measured in -dB) between the input and output with the switch off (NO).
4
PS8695B
03/01/05
PI5V330A Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Test Circuits
DC HP4195A S1 R1 T2
0.1 mF
HP41952A PI5V330A
HP41800A 0.1 mF 150
HP11667A
Figure 5. Differential Gain/Phase
+5.0V
VCC
3V
IN
S
D
75
PI5V330A
VOUT
Digital Input Analog Output tON
50%
50%
20pF
90%
90% tOFF
GND
EN
Figure 6. Switching Time
HP4195A S1 HP11667A R1 T1
PI5V330A 150
Figure 7. Gain/Phase, Crosstalk, Off-Isolation
5
PS8695B
03/01/05
PI5V330A Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Packaging Mechanical: 16-pin SOIC (S)
16
.2914 .2992
7.40 7.60
.010 0.254 x 45 .029 0.737
1
.398 10.10 .413 10.50
0-8
.0091 0.23 .0125 0.32
.020 0.508 .030 0.762
.0926 2.35 .1043 2.64
SEATING PLANE
0.41 .016 1.27 .050
.394 .419 10.00 10.65
.050 BSC 1.27
.013 .020 0.33 0.51
.0040 .0118
0.10 0.30
X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS
Packaging Mechanical: 16-pin SOIC (W)
16
.149 .157
3.78 3.99
.0099 .0196
0.25 x 45 0.50
1
.386 .393 9.80 10.00
.0155 .0260 0.393 0.660 REF
0-8
0.41 1.27
.0075 .0098
.016 .050
0.19 0.25
.053 .068
1.35 1.75
SEATING PLANE
.2284 .2440 5.80 6.20
.050 BSC 1.27
.013 .020 0.330 0.508
.0040 0.10 .0098 0.25
X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS
6
PS8695B
03/01/05
PI5V330A Low On-Resistance Wideband/Video Quad 2-Channel Mux/DeMux Packaging Mechanical: 16-pin QSOP (Q)
16
.008 0.20 MIN.
.150 .157
3.81 3.99
.008 .013 0.20 0.33
Guage Plane
.010 0.254
1
.189 .197 4.80 5.00
Detail A
.016 .035 0.41 0.89
.041 1.04 REF
0-6
.015 x 45 0.38
.053 1.35 .069 1.75
Detail A
.008 0.203 REF
.007 .010
0.178 0.254
SEATING PLANE
.004 0.101 .010 0.254
0.41 .016 1.27 .050
.228 .244 5.79 6.19
.025 BSC 0.635
.008 .012 0.203 0.305
X.XX DENOTES DIMENSIONS IN MILLIMETERS X.XX
Ordering Information
Ordering Code PI5V330AS PI5V330ASE PI5V330AW PI5V330AWE PI5V330AQ PI5V330AQE Package Code S S W W Q Q Package Description 16-pin 300-mil wide plastic SOIC Pb-free & Green, 16-pin 300-mil wide plastic SOIC 16-pin 150-mil wide plastic SOIC Pb-free & Green, 16-pin 150-mil wide plastic SOIC 16-pin 150-mil wide plastic QSOP Pb-free & Green, 16-pin 150-mil wide plastic QSOP
Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/
Pericom Semiconductor Corporation * 1-800-435-2336 * www.pericom.com
7
PS8695B 03/01/05

▲Up To Search▲

Price & Availability of PI5V330A

	To Download PI5V330A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .